Womens Day Budget Decorating / Photographer - Michael Partentio
Stylist - Donna Talley, Regional Producer and Editor for Meredith Publications
I have had this tutorial in the works for a while now and am happy to finally be sharing the method I use for sewing curtains with lining. Although I have tried a few variations, the following is what works best for me – and hopefully for you too!
Please read through all instructions before beginning. This tutorial is for curtain panels using one width (54”) of fabric.
Measurements
Determine the finished length of your curtain panel. This measurement will be based on the placement of your curtain rod as well as how you will be hanging your curtains, i.e. from rings, through a rod pocket, etc.
For the main fabric you will need the finished length plus 8 inches for the bottom hem and 6 inches for the top hem, times the number of panels you will be making. (I always add a few inches to this number just to make sure I have enough fabric.) If you are using a fabric with a pattern you will have to take the repeat of the pattern into consideration. Meaning, every panel should begin and end at the same point on the fabric. You most likely will have purchase additional yardage in order for all the panels to be identical.
For the lining you will need the finished length of the curtain minus 1 inch (as the lining will be shorter than the main fabric), plus 6 inches for the bottom hem and 6 inches for the top hem, times the number of panels.
Optional: For the interlining you will need the finished length of the curtain minus 2 inches plus 6 inches for the top hem. Most times I only use interlining if I am making silk curtains. Interlining is a felt like material - shown below - which adds weight and body to the curtains.
Cut all fabric pieces according to above measurements. After cutting the proper lengths of fabric, the lining and interlining panels should be cut to 49 ¾” wide. The main fabric should be cut to 54” wide by removing the side edges. If your main fabric needs to be shorter in width in order to remove the edges, simply deduct 4 ¼” to determine the width of the lining and interlining.
Sew Bottom Hems
The first sewing step to making your curtain panels is hemming the bottom of the main fabric and the lining – the interlining is not hemmed. To make the bottom hem of the main fabric, press under the bottom edge of the fabric 8 inches using an iron set to the proper temperature for your fabric.
Fold under and press to create a 4 inch hem. Pin and sew. Repeat for all main fabric curtain panels.
Repeat process with lining - only this time press under bottom edge of fabric 6 inches to create a 3 inch hem.
Using the main fabric, fold and press the outside and inside edges of the curtain panel 2 inches. Fold under to create a 1 inch hem on each side. Repeat with all main fabric panels.
Assembling the Curtain
Place curtain panel on flat surface with right side down (wrong side up).
Optional: If using interlining place interlining on top of panel, sliding edges of interlining under both side hems of the main curtain fabric. Make sure to line up the top of the interlining with the top of the curtain panel. It should be about 2 inches shorter than the main curtain fabric.
Place lining – right side up – on top of interlining and under both side hems of the main curtain fabric. Make sure to line up the top of the lining with the top of the curtain panel. Your lining should be about 1 inch shorter than the main curtain fabric and 1 inch longer than the interlining. By cutting the width of the lining and interlining pieces slightly smaller than the width of the finished curtain panel you should have no problem getting the three pieces of fabric to work together.
Pin two (or three if using interlining) layers in place and sew.
Create Top Hem
Fold and press under two (or three if using interlining) layers 6 inches. Fold under again to create a 3 inch top hem. Pin and sew.
Hang curtains using drapery pins, clip rings or through the top pocket hem.
0 comments:
Post a Comment